Commercial Sealcoating for Ypsilanti Parking Lots
Commercial sealcoating installation in Ypsilanti, MI follows a set order: clean the lot, repair what needs repair, apply the coating in dry weather, then keep traffic off until it dries. Sealcoating protects asphalt that is still sound. It does not fix a failed base. We handle asphalt sealcoating for business lots, and the steps below show what to expect and what to plan for.
What commercial sealcoating can protect
Sealcoating is a thin, protective layer of sealer applied over the surface of existing asphalt. It helps shield the binder (the glue that holds the stone together) from sun, water, oil and salt. On a lot that is sound but starting to look gray and worn, it slows surface wear and cuts down how much moisture gets in.
What it cannot do is rebuild the base, the compacted stone layer under the asphalt. If a section has sunk, pumps water, or has deep potholes, coating over it only hides the problem for a short time. The same goes for alligator cracking, the web of interlocking cracks that shows the layer underneath has lost support.
| What you see | Usual next step |
|---|---|
| Faded, dry surface, hairline cracks | Sealcoating after cleaning and crack work |
| Wide open cracks, isolated soft spots | Repair first, then coat |
| Deep potholes, large depressions, web-like cracking | Ask about patching or asphalt resurfacing before any coating |
| Lot failing across most of its area | Discuss full replacement through commercial asphalt paving |
If you are unsure which row your lot belongs in, ask for an honest assessment before you approve coating. A good walk-through should tell you where coating makes sense and where it will not.
How crews prepare a parking lot surface
Preparation decides how well the sealer bonds. Most of the labor in a sealcoating job happens before any product goes down.
- Clear the surface. Crews sweep and blow off loose stone, dirt, leaves and trash. Grass and weeds growing in cracks and along edges get removed.
- Treat oil and fuel spots. Sealer does not stick well to petroleum stains. Spots in parking stalls and near dumpsters are usually scraped, cleaned or primed so the coating can grab.
- Fill open cracks. Cracks wide enough to hold water are cleaned and filled before coating. Sealer alone will not bridge them for long.
- Repair damaged patches. Failed spots are cut out and patched, or flagged for a larger repair.
- Apply the coating. Sealer goes on in even coats, with hand work along curbs, islands and edges. Stall lines are typically repainted after the sealer has dried.
A dry, sound surface matters because water trapped under sealer keeps it from bonding and can lead to peeling. Damp pavement, standing puddles or a cold, wet morning are reasons for a crew to wait. If someone offers to coat in poor conditions, ask how they plan to get a good bond.
Plan lot access and reopening
For a business, the coating is the easy part. Keeping customers, tenants and deliveries moving is the harder one. Talk it through before the date is set.
- Decide which entrances can stay open and which close first. Work is often done in sections so part of the lot stays usable.
- Tell tenants, staff and delivery drivers ahead of time where to park and which doors to use.
- Pick a day and hours that suit your traffic. A lot that serves a weekday office has different needs than one beside a restaurant or clinic.
- Plan for barricades and signage so no one drives onto wet sealer.
Drying and reopening time depend on weather, temperature, humidity, how thick the coat is and how much sun the lot gets. A shaded corner can stay tacky longer than an open stretch. Because of that, we do not like to promise a fixed cure time. Agree on a reopening plan with the contractor, and expect that a damp or cool day can push it back. Many crews ask for traffic to stay off for a day or more, and heavy trucks and sharp turning often wait longer.
Michigan weather and a practical next step
Michigan winters bring snow, plow blades, de-icing salt and freeze-thaw cycles, where water seeps into pavement, freezes, expands and thaws again. That cycle widens small cracks into bigger ones. It is the main reason a sealed, crack-filled lot tends to hold up better than a bare one. This applies whether your property is in Ypsilanti, Ann Arbor or Belleville.
Timing matters as much as the product. Sealcoating generally needs dry pavement and mild, rising temperatures, so the best windows in Michigan usually fall between late spring and early fall. Cool, damp November and December conditions can limit what a crew can do, and shorter days slow drying. If your lot needs work late in the year, confirm that the pavement and the forecast are suitable before committing. Sometimes the right call is to repair cracks now and coat when spring weather settles.
Before you call for an estimate, walk the lot and make a short list:
- Damaged areas, such as potholes, sunken spots and wide cracks
- Places where water collects after rain or snowmelt
- Entrances, loading zones and the times of day when access matters most
Bring that list to the conversation. Our guide to maintaining asphalt pavement covers the routine upkeep that goes with it. We offer a free estimate, so you can compare a coating-only plan with repairs or resurfacing before you decide.
Common questions
When can a parking lot reopen after sealcoating?
It depends on temperature, humidity, sun and how thick the coat is. Many crews ask for traffic to stay off for 24 to 48 hours, and your contractor should confirm the plan for your lot once the work is done.
Does commercial sealcoating fix potholes or cracking?
No. Sealer protects the surface of sound pavement. Potholes, sunken areas and wide cracks need patching or resurfacing first, and cracks should be filled before coating.
Can a lot be sealcoated in late fall in Michigan?
Sometimes, if the pavement is dry and temperatures are mild enough for the sealer to cure. Cool, damp weather in November and December often rules out a good application, so confirm conditions before scheduling.
Areas we serve
Our services
Have a question about your project? Call (855) 432-7302
